Gold plating is a method of depositing a thin layer of gold onto the surface of another metal, most often copper or silver (to make silver-gilt), by chemical or electrochemical plating
by leopard jewelry. In this article, we explain its steps drying gold plated jewelryHow Gold Plating is Done, Step by Step
If you’re looking for the highest-quality, demi-fine jewelry, a vermeil collection with thick plating in 14 k to 18 k gold would be a good choice. If you don’t mind a lower base metal, gold filled pieces are probably your best bet when it comes to long-lasting and durable jewelry
Gold plated – sometimes called electroplated – items are made with a layer of gold on the surface over another type of metal underneath. On some occasions, items are gold plated to try and fool buyers or cash-for-gold operators. But for the most part, plating is done to enhance the look or wearability of a piece of jewelry
Gold plating is an easy technique, but before beginning the process, make sure your plater follows the best practices for best plating results
Gold plating steps
Surface Preparation
The surface of the metal to be plated must be very clean, so oils or dirt must be removed, and the piece must be polished. Surface preparation can include stripping, polishing, sandblasting, tumbling, etc. The use of solvents, abrasive materials, alkaline cleaners, acid etch, water, or a combination can be used. Typical methods to clean include acid or non-acid ultrasonic bath and a high rpm rouge wheel polishing. This is necessary for two reasons:
To improve adherence. (Dust and dirt interfere with the plated metals adhering to the jewelry piece.)
To keep the plating tanks free of contaminants
Cleaning
After the surface is prepared, and a visual inspection is done, electrocleaning, ultrasonic cleaning, or steaming, usually takes place. This second, deeper, cleaning step must follow to ensure metal is free of oils and dirt, which helps produce superior plating results. Steam cleaning blasts off any remaining oils that managed to hang on during the polishing phase. Take special note of intricate jewelry that has many nooks and crannies
Rinse
.The piece is rinsed thoroughly with water to remove any cleaning agents
Strike
A strike layer — also called a flash layer — adheres a thin layer of high-quality nickel plating to the base metal
In order to improve the bonding between the plating and the underlying surface, occasionally a buffer layer must be applied between them. With costume jewelry the base metal would contaminate the tanks with the gold in them, so a different metal is plated prior to the gold plating.
Additionally this step is used when the base metal, like copper, is known to atomically migrate outside of the gold layer to create spots of tarnish after plating. This strike step creates a barrier between the reactive base metal and the plated metal. This extends the life of the bright gold plating.
Rinse Again
The piece is rinsed thoroughly with water to remove any cleaning agents
Base Coat
If a base coat below gold is used, it is usually nickel.There can be many layers of plating done on one particular piece. For example a gold-plated silver article is usually a silver substrate with layers of copper, nickel, and gold deposited on top of it
Final Coating
With time, temperature and voltage carefully controlled, the piece is submerged into the plating solution to attract ions of gold or the final metal that will show on the surface. Different metals require different voltages and temperatures
The items to be plated are hung from a cathode bar, which is a pole with a negative electrical charge going through it. The pieces of jewelry connected to the cathode bar are also negatively charged. When the jewelry items are submerged in the tank an electrical charge is applied and the negatively charged jewelry attracts the positively charged ions present in the solution. The positively charged metal ions are submersed in the solution bath. When the cathode bar is lowered into the bath the metal jewelry gets plated
The plating thickness can be controlled by adjusting the immersion time in the plating tank
Final Rinse
Rinse off the pieces with water and then hang them to dry.
Drying
The pieces are hung, preferably not touching each other, in order to dry.
Repeat – if Necessary
Occasionally, the immersion step into the chosen plating metal needs to be repeated. In order to improve the bonding between the plating and the underlying surface, occasionally a buffer layer must be applied between them
After that step, rinsing and drying needs to be done
Gold plating wears out over time and can flake off, exposing the base metal underneath. It also loses its luster and fades with time. In general, plating can last for up to two years with proper care. The best way to deal with tarnished pieces is to have the piece replated when required
Leopard jewelry is at your service with the best plating quality